CD / DVDが正しく書き込まれない

MediaMonkey の書き込みエンジンとの非互換性を引き起こす可能性がある状況がいくつかあります。

  1. 一部のシステムでは、書き込みに管理者権限が必要です。「エラー: 書き込み可能なドライブがありません!」というエラーが表示される場合があります。MediaMonkey を起動する場所を右クリックして、[管理者として実行] を選択できます。
  2. MediaMonkey は、ハード ドライブ上の CD イメージに書き込むことができる Nero ImageDrive などの仮想 CD ソフトウェアと互換性がない場合があります。このような場合、CD または DVD の書き込み時に MediaMonkey が一時的にフリーズしたり、クラッシュしたり、デバイスがロックされたりすることがあります。この問題を解決するには、ImageDrive をアンインストールするか無効にします。
  3. 複数のドライブがある場合は、外付け CD/DVD ドライブを取り外してみてください。システムによっては、外付け CD/DVD ドライブが内部ドライブに干渉する場合があります。
  4. 「イメージ レイアウトを書き込めませんでした」というエラーが表示される場合は、MediaMonkey が特定のブランドのメディアを使用して、選択した速度でディスクを正常に書き込めないことが原因である可能性があります。速度を落として書き込んでみてください。また、宛先ファイル名マスクを <アーティスト> – <タイトル> のように単純なものに簡略化してみてください。
  5. 問題がオーディオ CD に固有のものである場合は、書き込みウィザードの最後のページで次の操作を試してください。
    • 「オンザフライオーディオ書き込み」を無効にする
    • 燃焼速度を下げる
    • 「ディスク・アット・ワンス」から「トラック・アット・ワンス」に変更
    • CD-Textの書き込みを無効にする
  6. バーナー ハードウェアによって直接報告される書き込みエラーには、ハードウェアの問題を示しているものがいくつかあります。これには次のものが含まれます。
    • センスコード 0 (センスなし) – ドライブが書き込みを停止し、メディアの回転が停止した場合にまれに発生します。
    • センスコード1(回復エラー) – 操作中に問題が発生したことを示す警告エラーメッセージ
    • センスコード2(準備ができていない) – MediaMonkeyが内部的に処理し、ユーザーに結果が提示されるドライブと挿入されたメディアの状態
    • センスコード 3 (メディアエラー) – メディア関連のエラーで、メディアが損傷しているか、書き込み速度がサポートされていないために書き込みが失敗したことを示します。
    • センスコード4(ハードウェアエラー) – 要求されたコマンドの実行に失敗したために発生したドライブハードウェア関連のエラー
    • センスコード5(不正な要求) – 保護されたディスクや互換性のないメディアなどのメディアの問題により、ハードウェアがコマンドの実行を拒否したり、コマンドを完了できなかったりする場合に最もよく発生します。
    • センス コード 6 (ユニット アテンション) – デバイスと通信するときに書き込みソフトウェア内で処理される通信コードと応答コード。

エラーコードの詳細については、 http://users.telenet.be/erik.deppe/troubleshooting_errorcodes.htmをご覧ください。

適用対象:

Translated automatically (see original)

CDs / DVDs don’t burn correctly

There are a couple of situations that can cause incompatibilities with MediaMonkey’s burning engine:

  1. On some systems burning requires Administrative rights. An error you may receive is ‘Error: No writable drive!’. You can right click where you launch MediaMonkey and select Run as Administrator.
  2. MediaMonkey is sometimes incompatible with Virtual CD software such as Nero ImageDrive, that allows you to write to a CD image on the hard drive. In such cases, it can cause MediaMonkey to temporarily freeze, crash, or lock the device when burning a CD or DVD. To resolve this issue, simply uninstall or disable ImageDrive.
  3. If you have multiple drives, try disconnecting any external CD/DVD drives–on some systems, they may interfere with internal drives.
  4. If you receive an error ‘Could not burn image layout’ it may be caused by MediaMonkey being unable to successfully burn the disk at the selected speed with the particular brand of Media being used. Try burning at a reduced speed. Additionally try to simplify Destination Filename mask to something simpler like <Artist> – <Title>
  5. If the problem is specific to Audio CDs, on the last page of the burn wizard try:
    • Disabling ‘On the fly audio burning’
    • Lower the speed of burning
    • Change from ‘Disk at once’ to ‘Track at once’
    • Disable burning of CD-Text
  6. There are several Burn errors that are directly reported by burner hardware that may indicate a hardware problem. These include:
    • Sense code 0 (No Sense) – Occurs rarely if the drive simply stops burning and media stopped spinning
    • Sense code 1 (Recovered Error) – Warning error messages that there was a problem during the operation
    • Sense code 2 (Not Ready) – Drive and inserted media state which MediaMonkey handles internally and user is prompted with result
    • Sense code 3 (Medium Error) – Media-related error that indicate either damage to the media or unsupported burn speed that causes burn to fail
    • Sense code 4 (Hardware Error) – Drive hardware-related errors due to failure to execute the requested command
    • Sense code 5 (Illegal Request) – Most commonly occurs when hardware refuse to execute or fails to complete a command due to media issues such as Protected Disk or incompatible media
    • Sense code 6 (Unit Attention) – Communication codes and response code that are handled within burning software when communicating with device.

Detailed info on error codes can be found at http://users.telenet.be/erik.deppe/troubleshooting_errorcodes.htm

Applies to:

Hide original

この記事は役に立ちましたか?